CALL US
920.337.0234
FSC Acquires Norcan

BOSCH
R132070400

TG: Plastic plain bearings

$0.44

BOSCH

MATERIAL:  R132070400

SUMMARY:  TG: Plastic plain bearings

Quantity in stock: 0

Add to Cart

Type R13207..00 is equipped with two flanges with different diameters. This type is specially designed for mounting in sheet metal shields up to a maximum thickness of 2 mm, ensuring the secure fit of the plastic plain bearings in the bearing plates.

 

Compensation gap

The flange is provided with a compensating gap “A” in the longitudinal direction. This almost compensates for dimensional deviations that occur as a result of moisture absorption or temperature changes, saves lubricant in lubricated bearings, and contributes to its distribution in the bearing.

technical illustration-R132070400-

Permissible p • v-values [N/cm2 • m/s]

d

Dry running

One-time grease lubrication

Continuous grease lubrication

mm

3 37 110 150
4
5
6
8 35 100 135
10
12

Permissible p ∙ v-values for an ambient temperature of 20°C

 

From the following diagram, the specific bearing pressures p in N/cm2 can be read for the peripheral speeds depending on the permissible p ∙ v value. For static loading capacity, a specific bearing pressure of p = 1400 N/cm2 is selected.

technical illustration-R132070400-

Radial load capacity

d

mm

3 4 5 6 8 10 12

Static load capacity

N

85 112 140 168 225 280 335

50 min–1

Dry running

N

85 112 140 168 225 265

One-time grease lubrication

N

85 112 140 168 225 280 335

Continuous grease lubrication

N

85 112 140 168 225 280 335

100 min–1

Dry running

N

85 112 140 143 133

One-time grease lubrication

N

85 112 140 168 225 280 335

Continuous grease lubrication

N

85 112 140 168 225 280 335

250 min–1

Dry running

N

57 53

One-time grease lubrication

N

85 112 140 166 154

Continuous grease lubrication

N

85 112 140 168 205
The axial load which can be absorbed by the collar must not exceed 25 % of the radial load capacity; for this, shaft collar diameter must correspond to dimension  "D" (see dimensions).
The specified values are valid for a bearing temperature ≤ 80 °C and an ambient temperature of 20 °C.

Technical data

technical illustration-R132070400-

Dimensions

d

D

D1

I

s

Tolerance for s

s1

Tolerance for s1

mm

mm

mm

mm

mm

mm

mm

mm

3 6 4.8 2 0.6 0
- 0.06
0.6 0
- 0.06
4 7 5.9
5 8 6.8
6 11 7.8
8 13 10.4 0.8 0.8
10 15 12.4
12 17 14.4 0
- 0.07

Calculation of the load capacity, service life and bearing clearance

▶ When mounting this type, be sure that the large flange comes to the side upon which the occurring axial forces are applied. The compensating gap “A” allows the plastic plain bearings to be compressed until the small flange can be easily rotated through the receiving bore in the bearing plate. For this, not that the gap points upwards during assembly and the left end is inserted first into the receiving bore. With a clockwise rotation, the plastic plain bearing pulls itself into the bore. If the assembly has been done properly, plastic plain bearings spring up again and are seated properly.

Mounting

Lubrication